Search Results (79)

The 16th century AD St. Barbara’s Church in Paternò, a town located at the SW foot of Mt. Etna volcano (Sicily, Italy), has since 2009 showed evident signs of structural instability and collapse. This is causing great concern among the local population and poses a growing hazard to the attendees to the masses. After precautionary closure of the church, we carried out geological, seismic, geophysical and geochemical surveys in order to shed light on the possible causes of the phenomenon. From the results of all surveys above, the presence of a hidden fault was hypothesized. The fault would prove to cross the west side of the church, parallel to its front portal, and continue both to the north and to the south of the edifice. It is part of a more complex system of faults that crosses the whole town of Paternò and is likely a result of the complex dynamics of Mt. Etna. This fault seems to also be a pathway for the upward flow of saline hydrothermal fluids, similar in composition to those emitted in nearby areas and whose corrosive action possibly contributed to the weakening of the rocks beneath the church. Temporal monitoring of several hydrological parameters (water temperature, water level and CO₂ content) in some sites in and around the church allowed a better understanding both of the fault dynamics and of the extent of hydrothermal influence in the studied area. Full article

The geochemical monitoring of volcanic activity today relies largely on remote sensing, but the combination of this approach together with soil gas monitoring, using the appropriate parameters, is still not widely used. The main purpose of this study was to correlate data from crater gas emissions with flank emissions of soil gases at Mt. Etna volcano from June 2006 to December 2020. Crater SO₂ fluxes were measured from fixed stations around the volcano using the DOAS technique and applying a modeled clear-sky spectrum. The SO₂/HCl ratio in the crater plume was measured with the OP-FTIR technique from a transportable instrument, using the sun as an IR source. Soil CO₂ efflux coupled with the ²²⁰Rn/²²²Rn activity ratio in soil gases (named SGDI) were measured at a fixed monitoring site on the east flank of Etna. All signals acquired were subject both to spectral analysis and to filtering of the periodic signals discovered. All filtered signals revealed changes that were nicely correlated both with other geophysical signals and with volcanic eruptions during the study period. Time lags between parameters were explained in terms of different modes of magma migration and storage inside the volcano before eruptions. A comprehensive dynamic degassing model is presented that allows for a better understanding of magma dynamics in an open-conduit volcano. Full article

Ground-based infrared cameras can be used effectively and safely to provide quantitative information about small to moderate-sized volcanic eruptions. This study describes an infrared camera that has been used to measure emissions from the Mt. Etna and Stromboli (Sicily, Italy) volcanoes. The camera provides calibrated brightness temperature images in a broadband (8–14 µm) channel that is used to determine height, plume ascent rate and volcanic cloud/plume temperature and emissivity at temporal sampling rates of up to 1 Hz. The camera can be operated in the field using a portable battery and includes a microprocessor, data storage and WiFi. The processing and analyses of the data are described with examples from the field experiments. The updraft speeds of the small eruptions at Stromboli are found to decay with a timescale of ∼10 min and the volcanic plumes reach thermal equilibrium within ∼2 min. A strong eruption of Mt. Etna on 1 April 2021 was found to reach ∼9 km, with ascent speeds of 10–20 ms⁻¹. The plume, mostly composed of the gases CO₂, water vapour and SO₂, became bent over by the prevailing winds at high levels, demonstrating the need for multiple cameras to accurately infer plume heights. Full article

In the framework of the Helmholtz ARCHES project, a multitude of robots, including rovers and drones, were prepared for the autonomous exploration of a test site at the foothills of Mt. Etna, Sicily—a terrain resembling extraterrestrial locations such as the Moon. To expand the suite of tools and sensors available for the exploration and investigation of the test site, we developed a laser-induced breakdown spectroscopy (LIBS) instrument for the geochemical analysis of local geological samples. In alignment with the mission scenario, this instrument is housed in a modular payload box that can be attached to the robotic arm of the Lightweight Rover Unit 2 (LRU2), allowing the rover to use the instrument autonomously in the field. A compact Nd:YAG laser is utilized for material ablation, generating a micro-plasma that is subsequently analyzed with a small fiber-coupled spectrometer. A single-board computer controls the LIBS hardware components for data acquisition. In this study, we provide details of the ARCHES LIBS instrument implementation, report on preceding laboratory tests where the LRU2 operated the LIBS module for the first time, and showcase the results obtained during the successful ARCHES space analogue demonstration mission campaign in summer 2022 in Sicily. Full article

An innovative mobile lidar device, developed to monitor volcanic plumes during explosive eruptions at Mt. Etna (Italy) and to analyse the optical properties of volcanic particles, was upgraded in October 2023 with the aim of improving volcanic plume retrievals. The new configuration of the lidar allows it to obtain new data on both the optical and the microphysical properties of the atmospheric aerosol. In fact, after the upgrade, the lidar is able to measure three backscattering coefficients, two extinction coefficients and two depolarisation ratios in a configuration defined as “state-of-the-art lidar”, where properties such as particle size distribution and the refractive index can be derived. During the lidar implementation, we were able to test the system’s performance through specific calibration measurements. A comparison in an aerosol-free region (7.2–12 km) between lidar signals at 1064 nm, 532 nm and 355 nm and the corresponding pure molecular profiles showed a relative difference of <1% between them for all the wavelengths, highlighting the good dynamic of the signals. The overlap correction allowed us to reduce the underestimation of the backscattering coefficient from 50% to 10% below 450 m and 750 m at both 355 and 532 nm, respectively. The correct alignment between the laser beam and the receiver optical chain was tested using the signal received from the different quadrants of the telescope, and the relative differences between the four directions were comparable to zero, within the margin of error. Finally, the first measurement results are shown and compared with results obtained by other instruments, with the aim of proving the ability of the upgraded system to more precisely characterise aerosol optical and microphysical properties. Full article

During explosive eruptions, tephra fallout represents one of the main volcanic hazards and can be extremely dangerous for air traffic, infrastructures, and human health. Here, we present a new technique aimed at identifying the area covered by tephra after an explosive event, based on processing PlanetScope imagery. We estimate the mean reflectance values of the visible (RGB) and near infrared (NIR) bands, analyzing pre- and post-eruptive data in specific areas and introducing a new index, which we call the ‘Tephra Fallout Index (TFI)’. We use the Google Earth Engine computing platform and define a threshold for the TFI of different eruptive events to distinguish the areas affected by the tephra fallout and quantify the surface coverage density. We apply our technique to the eruptive events occurring in 2021 at Mt. Etna (Italy), which mainly involved the eastern flank of the volcano, sometimes two or three times within a day, making field surveys difficult. Whenever possible, we compare our results with field data and find an optimal match. This work could have important implications for the identification and quantification of short-term volcanic hazard assessments in near real-time during a volcanic eruption, but also for the mapping of other hazardous events worldwide. Full article

An in-depth analysis of the orophilous vegetation dominated by Juniperus hemisphaerica in Sicily, based on literature data and unpublished relevés, is presented. A total of 156 phytosociological relevés were processed and analyzed using classification and ordination methods. Overall, 151 vascular plant species were recorded, of which 38% were endemic species, with a dominant hemicryptophytic biological form (49%). Classification of the relevés, supported by ordination, showed two main vegetation groups: one including the Juniperus communities of Mt. Madonie (Cerastio tomentosi–Juniperetum hemisphaericae and Pruno cupanianae–Juniperetum hemisphaericae), and the other including the vegetation of Mt. Etna (Bellardiochloo aetnensis–Juniperetum hemisphaericae and Roso siculae–Juniperetum hemisphaericae ass. nova). Furthermore, a new alliance, Berberido aetnensis–Juniperion hemisphericae, is proposed for Sicily. Full article

This paper analyses the net social benefits deriving from the medium-scale production of geopolymers based on volcanic ash compared to traditional cementitious materials used in construction and restoration sectors. In contrast to the existing literature grounded on the physical and mechanical characterization of geopolymers, our analysis considers two aspects: public finance savings from avoiding the disposal of volcanic ash in landfills and environmental benefits deriving from reduction in CO₂ releases due to the production process at room temperature. Our case study focuses on the reuse of natural waste, namely the volcanic ash of the Mt. Etna volcano (Italy), whose disposal involves significant costs for society. Its use in the alkaline activation process avoids the exploitation of natural resources. Considering the huge amount of volcanic ash from Mt. Etna that falls on the urban areas of Eastern Sicily, the results show relevant economic benefits, in terms of both avoided costs and tax reductions for the citizens. Alongside these, significant environmental benefits are evidenced thanks to the release of up to 78% lower CO₂ emissions by synthesised materials with volcanic ash than by traditional cementitious ones. Overall, the social cost savings compared to traditional materials is 0.339 EUR/kg for geopolymer. Full article

The Experiment to Study Thunderstorm High-Energy Radiation (ESTHER) is a small project of the Italian National Institute for Astrophysics (INAF), devoted to the study of high-energy emissions from thunderstorms, such as Terrestrial Gamma-ray Flashes and gamma-ray glows, which will start in 2024. In order to reduce the absorption typically undergone by gamma-ray radiation in the lower layers of the atmosphere and make these events detectable on the ground, the ESTHER set-up will be installed at high altitudes on Mt. Etna (Italy). We carried out a detailed analysis of lightning occurrence in this geographic region in order to test how suitable such a location is for the installation of a detection system to investigate thunderstorms and related emissions. The analysis pointed out a strong clustering of lightning in the proximity of the mountain peak and over the main volcano craters, where the frequent presence of volcanic ashes could increase, under the conditions of humid air typical of thunderstorms, electrical conductivity. An estimate of the gamma-ray absorption in the air undergone by typical TGF radiation allowed us to evaluate the suitability of two possible installation sites suggested for the project. This study represents a preliminary work for ESTHER and serves as a launching pad for future analyses. Full article

Volcanic eruptions pose a major natural hazard influencing the environment, climate and human beings at different temporal and spatial scales. Nevertheless, several volcanoes worldwide are poorly monitored and assessing the impact of their eruptions remains, in some cases, challenging. Nowadays, different numerical dispersion models are largely employed in order to evaluate the potential effects of volcanic plume dispersion due to the transport of ash and gases. On 28 August 2019, both Mt. Etna and Stromboli had eruptive activity; Mt. Etna was characterised by mild-Strombolian activity at summit craters, while at Stromboli volcano, a paroxysmal event occurred, which interrupted the ordinary typical-steady Strombolian activity. Here, we explore the spatial dispersion of volcanic sulphur dioxide (SO${}_2$) gas plumes in the atmosphere, at both volcanoes, using the Weather Research and Forecasting model coupled with Chemistry (WRF-Chem) considering the ground-measured SO${}_2$ amounts and the plume-height as time-variable eruptive source parameters. The performance of WRF-Chem was assessed by cross-correlating the simulated SO${}_2$ dispersion maps with data retrieved by TROPOMI and OMI sensors. The results show a feasible agreement between the modelled dispersion maps and TROPOMI satellite for both volcanoes, with spatial pattern retrievals and a total mass of dispersed SO${}_2$ of the same order of magnitude. Predicted total SO${}_2$ mass for Stromboli might be underestimated due to the inhibition from ground to resolve the sin-eruptive SO${}_2$ emission due to the extreme ash-rich volcanic plume released during the paroxysm. This study demonstrates the feasibility of a WRF-Chem model with time-variable ESPs in simultaneously reproducing two eruptive plumes with different SO${}_2$ emission and their dispersion into the atmosphere. The operational implementation of this method could represent effective support for the assessment of local-to-regional air quality and flight security and, in case of particularly intense events, also on a global scale. Full article

Saponaria sicula Raf. grows in Sicily, Sardinia, and Algeria on limestone cliffs and volcanic sands 1300–2500 m above sea level. The aim of the present study was to investigate how the pedo-climatic conditions influence the micromorphological, phytochemical, and biological properties of Sicilian S. sicula leaves collected in the Madonie Mountains (SsM) and on Etna Mt (SsE). Micromorphological investigations revealed that leaves from SsM had a higher amount of calcium oxalate druses in the mesophyll and a more intense blue–green staining with Toluidine blue O, indicating a higher content of polyphenols. These data were confirmed by phytochemical analyses carried out on hydroalcoholic extracts, which showed a higher content of total phenols (8.56 ± 0.57 g GAE/100 g DE) and flavonoids (6.09 ± 0.17 g RE/100 g DE) in SsM. Sixty-four compounds were identified by LC-DAD-ESI-MS analysis with propelargonidin dimer as the most abundant compound (10.49% and 10.19% in SsM and SsE, respectively). The higher polyphenol content of SsM leaves matches also with their biological activity, identifying SsM extract as the strongest plant complex (IC₅₀ 2.75–477.30 µg/mL). In conclusion, the present study experimentally demonstrates that not only climatic differences but also soil characteristics affect the micromorphological, phytochemical, and biological features of this plant species. Full article

Mt Etna in Sicily hosts a bryophyte floristic richness of 306 taxa, corresponding to 259 mosses, 43 liverworts, and 4 hornworts. Species richness shows a hump-shaped relationship with the elevation, with a peak at 1200–1700 m a.s.l. Chorotype patterns clearly change along an altitudinal gradient, from the Mediterranean, located at 0–300 m a.s.l., to Arctic-montane and boreo-Arctic montane at 1800–2700 m a.s.l., showing a correlation with the bioclimatic belts identified for the Mt Etna. In regard to the life form pattern, the turf species are the most represented in each elevation gradient, except at 2300–2700 m a.s.l. where the tuft species are prevalent. The life strategy pattern shows the colonists as the prevailing species, featured by an increasing trend up to 2200 m of elevation; above this limit, they are exceeded by the perennial stayers. Furthermore, taking into consideration the red-listed species (at the European and/or Italian level), as well as the species of phytogeographical interest, it was possible to identify the high bryophyte conservation priority areas; these areas are located in thermo-Mediterranean and oro-Mediterranean bioclimatic belts, the latter corresponding to the oldest substrates of the volcano where some of the most interesting bryophyte glacial relicts find refuge. Full article

Tephra dispersal and fallout resulting from explosive activity of Mt. Etna (Italy) represent a significant threat to the surrounding inhabited areas as well as to aviation operations. An early-warning system aimed at foreseeing the onset of paroxysmal activity has been developed, combining a thermal infrared camera, infrasonic network, and a weather radar. In this way, it is possible to identify the onset of a lava fountain as well as to determine the associated mass eruption rate (MER) and top plume height (H_TP). The new methodology, defined as the paroxysmal early-warning (PEW) alert system, is based on the analysis of some explosive eruptions that occurred between 2011 and 2021 at Etna, simultaneously observed by the thermal camera and infrasound systems dislocated around the summit eruptive craters, and by the weather radar, located at about 32 km from the summit craters. This work represents an important step towards the mitigation of the potential impact associated with the tephra dispersal and fallout during paroxysms at Etna, which can be applied to other volcanoes with similar activity and monitoring strategies. Full article

Volcanic plume height is one the most important features of explosive activity; thus, it is a parameter of interest for volcanic monitoring that can be retrieved using different remote sensing techniques. Among them, calibrated visible cameras have demonstrated to be a promising alternative during daylight hours, mainly due to their low cost and low uncertainty in the results. However, currently these measurements are generally not fully automatic. In this paper, we present a new, interactive, open-source MATLAB tool, named ‘Plume Height Analyzer’ (PHA), which is able to analyze images and videos of explosive eruptions derived from visible cameras, with the objective of automatically identifying the temporal evolution of eruption columns. PHA is a self-customizing tool, i.e., before operational use, the user must perform an iterative calibration procedure based on the analysis of images of previous eruptions of the volcanic system of interest, under different eruptive, atmospheric and illumination conditions. The images used for the calibration step allow the computation of ad hoc expressions to set the model parameters used to recognize the volcanic plume in new images, which are controlled by their individual characteristics. Thereby, the number of frames used in the calibration procedure will control the goodness of the model to analyze new videos/images and the range of eruption, atmospheric, and illumination conditions for which the program will return reliable results. This also allows improvement of the performance of the program as new data become available for the calibration, for which PHA includes ad hoc routines. PHA has been tested on a wide set of videos from recent explosive activity at Mt. Etna, in Italy, and may represent a first approximation toward a real-time analysis of column height using visible cameras on erupting volcanoes. Full article

Between 2020 and 2022, more than sixty lava fountains occurred at Mt. Etna (Italy), which formed high eruption columns rising up to 15 km above sea level (a.s.l.). During those events, several ballistics fell around the summit craters, sometimes reaching touristic areas. The rather frequent activity poses questions on how the impact associated with the fallout of those particles, can be estimated. In this work, we present field data collected soon after the lava fountain on 21 February 2022. This event produced a volcanic plume of about 10 km a.s.l. which was directed toward the southeast. Several ballistics fell in the area of the Barbagallo Craters (just southeast of the summit area at around 2900 m a.s.l.), which is one of the most popular touristic areas on Etna. Hence, we collected several samples and performed laboratory analyses in order to retrieve their size, shape and density. Those values together with a quantitative analysis of the lava fountain were compared with results obtained by a free-available calculator of ballistic trajectories named the ‘Eject!’. A similar approach was hence applied to other lava fountains of the 2020–2022 sequence for which the fallout of large clasts was reported. This work is a first step to identifying in near real-time the area affected by the fallout of ballistics during Etna lava fountains and quantifying their hazard. Full article